aniCon
100+
Yuklanmalar
Hamma uchun
info
Bu ilova haqida
Use aniCon to control your aniLight product via Bluetooth Low Energy (BLE), including changing device settings (such as Light brightness, RGB light color, White color temperature, Delay time, etc.) and performing Over-the-Air (OTA) firmware update to keep your device up to date.
First, you need to operate aniLight to enter BLE mode:
① Power aniLight off: Press and hold the left PWR button for 3 seconds until red light runs counterclockwise once.
② Enter BLE mode: Press and hold the right SET button. While SET button is held, press and hold PWR button for 3 seconds until BLUE (not green) light runs clockwise once. Then release both buttons.
Go to SCAN tab to scan and find aniLight device with the name of "aniLight_1". Tap it to connect. The BLE icon in the top-right corner will turn to active after connected. Tap that icon to connect/disconnect it.
Go to DEVICE tab to change its name or perform firmware update.
Go to ANILIGHT tab to change settings of the connected aniLight.
You need to press the SAVE button to save your changes to the device.
Go to Help tab for more detailed information.
BLE mode needs more power to run. So after finishing the settings change, re-enter the normal mode:
① Power the unit off.
② Power the unit on normally: Press and hold PWR button for 3 seconds until green light runs clockwise once.
We are now working on an improved firmware, and will release it soon in the next version.
First, you need to operate aniLight to enter BLE mode:
① Power aniLight off: Press and hold the left PWR button for 3 seconds until red light runs counterclockwise once.
② Enter BLE mode: Press and hold the right SET button. While SET button is held, press and hold PWR button for 3 seconds until BLUE (not green) light runs clockwise once. Then release both buttons.
Go to SCAN tab to scan and find aniLight device with the name of "aniLight_1". Tap it to connect. The BLE icon in the top-right corner will turn to active after connected. Tap that icon to connect/disconnect it.
Go to DEVICE tab to change its name or perform firmware update.
Go to ANILIGHT tab to change settings of the connected aniLight.
You need to press the SAVE button to save your changes to the device.
Go to Help tab for more detailed information.
BLE mode needs more power to run. So after finishing the settings change, re-enter the normal mode:
① Power the unit off.
② Power the unit on normally: Press and hold PWR button for 3 seconds until green light runs clockwise once.
We are now working on an improved firmware, and will release it soon in the next version.
Oxirgi yangilanish
Xavfsizlik — dastur ishlab chiquvchilar maʼlumotlaringizni qanday jamlashi va ulashishini tushinishdan boshlanadi. Maʼlumotlar maxfiyligi va xavfsizlik amaliyotlari ilovadan foydalanish, hudud va yoshga qarab farq qilishi mumkin. Bu axborot dastur ishlab chiquvchi tomonidan taqdim etilgan va keyinchalik yangilanishi mumkin.
Nima yangiliklar
aniCon Ver 1.0.2:
* Provided the firmware (v1.2) update for aniLight.
Please refer to the Help tab for the detailed information.
aniLight button operations for Settings have been changed with the new firmware v1.2:
* Single press SET button to change Brightness.
* Double press SET button to change Color.
* Triple press SET button to change Delay Time.
When the desired Setting value is reached, press SET button again to save and exit Settings.
Or press PWR button to cancel and exit Settings.
* Provided the firmware (v1.2) update for aniLight.
Please refer to the Help tab for the detailed information.
aniLight button operations for Settings have been changed with the new firmware v1.2:
* Single press SET button to change Brightness.
* Double press SET button to change Color.
* Triple press SET button to change Delay Time.
When the desired Setting value is reached, press SET button again to save and exit Settings.
Or press PWR button to cancel and exit Settings.
