QE Tools

QualityEdify

About this app

Welcome to QualityEdify Tools, the cutting-edge mobile application designed to meet all your daily quality control requirements. Featuring an extensive array of over 50 functions, QualityEdify Tools encompasses comprehensive calculations and invaluable information on welding, coating, piping, and non-destructive examination formulas. Whether you're a novice embarking on your quality inspection journey, a seasoned professional, or anyone in between, QualityEdify Tools is your ultimate solution.

Tools included, but not limited to:

### #1. Welding & Piping:

• Heat Input Calculation, Storage And Share
• Mitre Fillet Weld Leg Length Calculation
• Carbon Equivalent Value Calculation
• All Weld Metal Tensile Test Calculation
• Butt Weld Consumable Calculation
• Hardness Conversion
• Pipe Schedule Table
• Api Steel Mechanical Features Data
• Stainless Steel Polishing Grit No. Data
• Transverse Tensile Test Calculation **[ - New added]**
• Welding Preheat Calculator **[ - New added]**
• ASME B31.3 Preheat Temp **[ - New added]**
• API 1104 Weld Acceptance **[ - New added]**
• ASME B31.3 Weld Undercut **[ - New added]**
• ASME IX P-Number Lookup **[ - New added]**
• ASME IX F-Number Lookup **[ - New added]**
• ASME B31.3 PWHT Guide **[ - New added]**
• AWS D1.1 Min Fillet Size **[ - New added]**

### #2. Coating

• Dry Film Thickness Calculation
• Wet Film Thickness Calculation
• Spreading Rate Calculation
• Consumption Of Paint Calculation
• Abrasive Blasting Consumption Calculation
• Spray Tip Size Guide Data
• Lighting Requirements Data
• Surface Conductivity ⇆ Concentration Calculation
• Replica Tape Data
• Holiday Detection Voltage Calculation
• Weight ⇆ Thickness Calculation (Hot-Dip Galvanizing)
• ISO 12944 Corrosivity Guide **[ - New added]**
• Coating Dew Point Calculator **[ - New added]**
• SSPC-PA 2 DFT Spot Check **[ - New added]**
• ISO 8503 Abrasive Profile **[ - New added]**
• Bresle Salt Calculator (ISO 8502) **[ - New added]**
• Paint Dilution Coverage Calculator **[ - New added]**

### #3. NDT

• Gamma Emission of Isotopes Data
• Focus To Film Distance Calculation
• Inverse Square Law Calculation
• Safe Working Distance Calculation
• Wave Equation
• Signal Amplitude Calculation
• Near Zone Calculation
• Acoustic Impedance Calculation
• Shell’s Law Calculation
• Beam Spread Angle Calculation
• MT Prod Technique (ASME Sec V) **[ - New added]**
• MT Coil Magnetization (ASME Sec V) **[ - New added]**
• MT Yoke Lift Test (ASME Sec V) **[ - New added]**
• MT Field Adequacy Check **[ - New added]**
• PT Dwell & Temp (ASME Sec V) **[ - New added]**
• API 1104 RT IQI Selection **[ - New added]**
• ASME V RT IQI Selection **[ - New added]**
• ASME V RT Geometric Unsharpness **[ - New added]**
• ASME V UT Calibration Block **[ - New added]**
• ASME V UT Gauge Calibrator **[ - New added]**
• API 1104 UT Weld Acceptance **[ - New added]**

What’s new

What’s New
Have been added 20+ powerful features to supercharge your workflow:

Welding & Piping: Added Transverse Tensile, Preheat, ASME P/F-Number lookups, API 1104, and AWS D1.1 calculators.

Coating: Added ISO 12944, Dew Point, SSPC-PA 2, Abrasive Profile, and Bresle Salt calculators.

NDT: New ASME Sec V support for MT/PT, RT IQI selection, and UT calibration tools.

Update now to experience the ultimate quality control suite!