StockCut — Cut List Optimizer
Contains ads
Everyone
info
10+
Downloads
Everyone
Learn more
About this app
Stop working out cut lists on the back of a delivery note.
Tell StockCut the lengths you can buy and the pieces you need. It works out which piece comes off which bar, in seconds, with as little offcut as it can find — and it counts your saw blade, which is where hand-written cut lists go wrong.
WHAT IT DOES
• Works out how to cut the job from fewer bars
• Accounts for kerf — every cut eats blade width, and ten cuts at 3 mm is 30 mm
• Shows each bar as a diagram, so you can read it at the saw
• Tells you the offcut left on every bar and the total waste percentage
• Warns you when a piece is longer than anything you can buy, instead of quietly dropping it
METRIC AND IMPERIAL
Millimetres, centimetres, metres, decimal inches, and fractional inches. Type 1 5/16" and it takes it — no converting to decimals in your head, no rounding errors creeping into a job.
BUILT FOR THE SITE, NOT THE OFFICE
• Works with no signal. Everything runs on the phone
• No account, no sign-up, no password
• Your jobs are never uploaded — they stay on your device
• Large type and big touch targets, for reading with safety glasses on
• Share a cut plan as an image or a PDF — send it to the apprentice, or print it
WHO IT IS FOR
Fabricators, welders, metalworkers, carpenters, timber framers, shopfitters, window and door installers, fencers, and anyone cutting from linear stock: steel tube, box section, angle, flat bar, rod, rebar, aluminium extrusion, timber studs, skirting, trim, pipe, and conduit. Use it as a cutting calculator for steel, wood, pipe, rod or aluminium.
If you buy material in fixed lengths and cut pieces from it, this saves you material on every job.
HOW IT WORKS
1. Enter the lengths you can buy — 6 m bars, 8 ft studs, whatever your supplier sells
2. Enter the pieces you need and how many
3. Set your blade width
4. Tap Optimize
You get a plan: bar by bar, cut by cut, with the offcut on each.
FREE
StockCut is free and supported by ads. There is no subscription, no trial, and nothing is locked. Ads are kept deliberately light — a banner, and an occasional full-screen ad after you tap Optimize, never while you are entering a job.
WHAT IT IS NOT
This is a 1D linear cut list optimizer. It solves bar, tube and length cutting. It does not do 2D sheet nesting for plywood or plate.
Tell StockCut the lengths you can buy and the pieces you need. It works out which piece comes off which bar, in seconds, with as little offcut as it can find — and it counts your saw blade, which is where hand-written cut lists go wrong.
WHAT IT DOES
• Works out how to cut the job from fewer bars
• Accounts for kerf — every cut eats blade width, and ten cuts at 3 mm is 30 mm
• Shows each bar as a diagram, so you can read it at the saw
• Tells you the offcut left on every bar and the total waste percentage
• Warns you when a piece is longer than anything you can buy, instead of quietly dropping it
METRIC AND IMPERIAL
Millimetres, centimetres, metres, decimal inches, and fractional inches. Type 1 5/16" and it takes it — no converting to decimals in your head, no rounding errors creeping into a job.
BUILT FOR THE SITE, NOT THE OFFICE
• Works with no signal. Everything runs on the phone
• No account, no sign-up, no password
• Your jobs are never uploaded — they stay on your device
• Large type and big touch targets, for reading with safety glasses on
• Share a cut plan as an image or a PDF — send it to the apprentice, or print it
WHO IT IS FOR
Fabricators, welders, metalworkers, carpenters, timber framers, shopfitters, window and door installers, fencers, and anyone cutting from linear stock: steel tube, box section, angle, flat bar, rod, rebar, aluminium extrusion, timber studs, skirting, trim, pipe, and conduit. Use it as a cutting calculator for steel, wood, pipe, rod or aluminium.
If you buy material in fixed lengths and cut pieces from it, this saves you material on every job.
HOW IT WORKS
1. Enter the lengths you can buy — 6 m bars, 8 ft studs, whatever your supplier sells
2. Enter the pieces you need and how many
3. Set your blade width
4. Tap Optimize
You get a plan: bar by bar, cut by cut, with the offcut on each.
FREE
StockCut is free and supported by ads. There is no subscription, no trial, and nothing is locked. Ads are kept deliberately light — a banner, and an occasional full-screen ad after you tap Optimize, never while you are entering a job.
WHAT IT IS NOT
This is a 1D linear cut list optimizer. It solves bar, tube and length cutting. It does not do 2D sheet nesting for plywood or plate.
Cutting calculator and cut list optimizer for metal, timber, pipe and rod.
Updated on
Safety starts with understanding how developers collect and share your data. Data privacy and security practices may vary based on your use, region, and age. The developer provided this information and may update it over time.
What’s new
Measurements now show their units. Removes an incorrect "In-app purchases" label — the app is free. Fixes a white flash when opening the app in dark mode.
Everyone
Learn moreApp support
About the developer
RAMESHKUMAR KANNAN
rameshkumaroff@gmail.com
India