Construction Expert A1 PRO
In-app purchases
5+
Downloads
Everyone
info
About this app
The ultimate construction calculator trusted by contractors, builders, carpenters, and engineers. Construction Expert A1 Pro replaces your $100+ hardware calculator with a smarter, more powerful app.
PROFESSIONAL CALCULATOR
- Full feet-inch-fraction math — enter dimensions the way you think
- Supports feet, inches, yards, meters, centimeters, millimeters
- Fractional entry (1/16 to 1/64 resolution) with auto-simplification
- Percentage, square, cube, square root, reciprocal
- D:M:S (degrees-minutes-seconds) and trigonometry (sin, cos, tan)
- Expression mode with 12 construction formula templates
- Running tape with save, share, and print
- 3 memory registers + cumulative memory with count/average
RIGHT ANGLE & ROOF FRAMING
- Pitch, rise, run, diagonal — solve any right triangle instantly
- Common rafter length, plumb cut, and level cut angles
- Hip/valley rafter with cheek cut angles
- Jack rafter lengths with on-center increment
- Irregular roof support (dual-pitch hip/valley)
- Rake wall stud lengths (ascending or descending)
- Roof area, squares, bundles, and 4×8 sheet count
- Interactive rafter diagrams
STAIR LAYOUT
- Total rise to finished risers and treads
- Riser adjustment (+/-) for code compliance
- Stringer length and inclination angle
- Open/closed stringer support
- Interactive stair diagram with all dimensions
7 TRADE CALCULATORS
- Electrical: Wire sizing (NEC), voltage drop, load calc, conduit fill, box fill, outlet spacing, service sizing
- Plumbing: Pipe sizing, DFU, water heater, fitting offsets, drain slope, pressure loss
- HVAC: BTU load, duct sizing, CFM, refrigerant charge, filter sizing
- Landscaping: Mulch, gravel, sod, irrigation, retaining wall, pavers
57 AREA & VOLUME SHAPES
- From simple squares to L-shaped rooms, gable walls, pipe volumes, and toruses
- Interactive diagrams with labeled dimensions
- Perimeter, surface area, and volume calculations
- Construction-specific shapes: concrete steps, retaining walls, trenches
50+ UNIT CONVERTERS
- Length, area, volume, weight, temperature, pressure, and more
- Construction-specific: concrete bags, rebar, CMU blocks, board feet
- Lumber, drywall, roofing, siding, flooring, insulation
- Electrical wire gauge, conduit, circuit breakers
- Plumbing pipes (PVC, copper, PEX), HVAC tonnage
- Aggregates: gravel, sand, topsoil, mulch, fill dirt
- Fasteners: nails, screws, bolts, anchors
MATERIAL ESTIMATION
- Board feet calculator
- Stud spacing and count
- Concrete volume (slabs, footings, columns)
- Roofing (squares, bundles, felt, ridge vent)
- Drywall sheets and accessories
- Baluster/spindle spacing
- Fence materials (posts, rails, pickets)
PROJECT MANAGEMENT
- Organize calculations by project
- Rich text notes with folder organization
- Photo attachments for calculations
- Star/favorite frequently used calculators
- Calculation history with search and filter
EXPORT & SHARE
- Professional PDF reports with company branding
- CSV spreadsheet export
- PNG image export
- Plain text sharing
- 7 specialized PDF generators (rafter, stair, fence, baluster, compound miter, materials, estimate)
CUSTOMIZATION
- Dark mode / Light mode / System theme
- 5 languages: English, Spanish, French, German, Arabic
- Fractional resolution (1/2 to 1/64)
- Imperial or Metric default units
- Home screen widgets
- Haptic feedback and sound effects
- Company branding for all exports
BUILT FOR PROFESSIONALS
Whether you're a general contractor estimating a bid, a framer cutting rafters, an electrician sizing wire, or a DIY homeowner planning a deck — Construction Expert A1 Pro has every calculation you need.
Download now and see why professionals are switching from their hardware calculators.
PROFESSIONAL CALCULATOR
- Full feet-inch-fraction math — enter dimensions the way you think
- Supports feet, inches, yards, meters, centimeters, millimeters
- Fractional entry (1/16 to 1/64 resolution) with auto-simplification
- Percentage, square, cube, square root, reciprocal
- D:M:S (degrees-minutes-seconds) and trigonometry (sin, cos, tan)
- Expression mode with 12 construction formula templates
- Running tape with save, share, and print
- 3 memory registers + cumulative memory with count/average
RIGHT ANGLE & ROOF FRAMING
- Pitch, rise, run, diagonal — solve any right triangle instantly
- Common rafter length, plumb cut, and level cut angles
- Hip/valley rafter with cheek cut angles
- Jack rafter lengths with on-center increment
- Irregular roof support (dual-pitch hip/valley)
- Rake wall stud lengths (ascending or descending)
- Roof area, squares, bundles, and 4×8 sheet count
- Interactive rafter diagrams
STAIR LAYOUT
- Total rise to finished risers and treads
- Riser adjustment (+/-) for code compliance
- Stringer length and inclination angle
- Open/closed stringer support
- Interactive stair diagram with all dimensions
7 TRADE CALCULATORS
- Electrical: Wire sizing (NEC), voltage drop, load calc, conduit fill, box fill, outlet spacing, service sizing
- Plumbing: Pipe sizing, DFU, water heater, fitting offsets, drain slope, pressure loss
- HVAC: BTU load, duct sizing, CFM, refrigerant charge, filter sizing
- Landscaping: Mulch, gravel, sod, irrigation, retaining wall, pavers
57 AREA & VOLUME SHAPES
- From simple squares to L-shaped rooms, gable walls, pipe volumes, and toruses
- Interactive diagrams with labeled dimensions
- Perimeter, surface area, and volume calculations
- Construction-specific shapes: concrete steps, retaining walls, trenches
50+ UNIT CONVERTERS
- Length, area, volume, weight, temperature, pressure, and more
- Construction-specific: concrete bags, rebar, CMU blocks, board feet
- Lumber, drywall, roofing, siding, flooring, insulation
- Electrical wire gauge, conduit, circuit breakers
- Plumbing pipes (PVC, copper, PEX), HVAC tonnage
- Aggregates: gravel, sand, topsoil, mulch, fill dirt
- Fasteners: nails, screws, bolts, anchors
MATERIAL ESTIMATION
- Board feet calculator
- Stud spacing and count
- Concrete volume (slabs, footings, columns)
- Roofing (squares, bundles, felt, ridge vent)
- Drywall sheets and accessories
- Baluster/spindle spacing
- Fence materials (posts, rails, pickets)
PROJECT MANAGEMENT
- Organize calculations by project
- Rich text notes with folder organization
- Photo attachments for calculations
- Star/favorite frequently used calculators
- Calculation history with search and filter
EXPORT & SHARE
- Professional PDF reports with company branding
- CSV spreadsheet export
- PNG image export
- Plain text sharing
- 7 specialized PDF generators (rafter, stair, fence, baluster, compound miter, materials, estimate)
CUSTOMIZATION
- Dark mode / Light mode / System theme
- 5 languages: English, Spanish, French, German, Arabic
- Fractional resolution (1/2 to 1/64)
- Imperial or Metric default units
- Home screen widgets
- Haptic feedback and sound effects
- Company branding for all exports
BUILT FOR PROFESSIONALS
Whether you're a general contractor estimating a bid, a framer cutting rafters, an electrician sizing wire, or a DIY homeowner planning a deck — Construction Expert A1 Pro has every calculation you need.
Download now and see why professionals are switching from their hardware calculators.
Updated on
Safety starts with understanding how developers collect and share your data. Data privacy and security practices may vary based on your use, region and age. The developer provided this information and may update it over time.
No data shared with third parties
Learn more about how developers declare sharing
No data collected
Learn more about how developers declare collection
What's new
Welcome to Construction Expert A1 Pro - the most powerful construction calculator app ever built!
- Full Construction calculator with feet-inch-fraction math
- 7 Trade calculators: Electrical, Plumbing, HVAC, Landscaping + more
- Right angle, roof rafter, hip/valley, jack rafter calculations
- Complete stair layout with stringer, risers, and treads
- Compound miter and crown molding angles
- Project management with notes and photo attachments
- PDF, CSV, and image export with company branding
- Full Construction calculator with feet-inch-fraction math
- 7 Trade calculators: Electrical, Plumbing, HVAC, Landscaping + more
- Right angle, roof rafter, hip/valley, jack rafter calculations
- Complete stair layout with stringer, risers, and treads
- Compound miter and crown molding angles
- Project management with notes and photo attachments
- PDF, CSV, and image export with company branding
App support
About the developer
Binary and Bricks Private Limited
techsupport@binaryandbricks.com
GAT NO-50, FLAT NO-306, SAI HIRA MOSHI HAVELI, PIMPRI CHINCHWAD
Pune, Maharashtra 412105
India
+91 88067 80101
